Hi Alan Well if you turn the belt over and run on the friction material the groove side has you will find that you can transmit two to three times the HP that...
Hi Paul The one I used on this setup is the 2 1/4 inch diameter. The full size dials on the inch HLV-H are 2 1/2 inch and are to big to use on the little 9...
Dennis, Your picture of the poly-vee grooved 3-step cone looks very fine. Wish mine looked that nice for its age to show off. My Dad machined poly grooves in...
Denny, how sweet that dial is to old worn out eyes! The grooved cones are also beautiful. Make a mistake and you're gonna break something cause they aint gonna...
I cannot find the pictures either. In the original post, all I can see are the two attachment windows, but with a message "attachment not stored???? What am...
If you're reading the posts from the message board the attachments are stripped off. You must change your group preferences to "Receive Posts By Mail", or...
... are stripped off. You must change your group preferences to "Receive Posts By Mail", or something similar to that. You probably must have preferences set...
Dennis, What a beautiful job. I wish my lathe looked half that nice, I suspect it didn't look that good the day it was made. :-) Question, do the marks on...
Hi All For you that do not get emails from your Yahoo South Bend lathe site I have uploaded these two pictures to my flicker photo site so you can take a look...
The large dial I have on the compound is a 100 increment dial which is correct by all lathe standards when equipped with a 10 pitch screw. SB on the 9 workshop...
There must be an echo in here! -:) ________________________________ From: guivret <erecgrim@...> To: southbendmanual@yahoogroups.com Sent: Sunday, November...
For those of you that have never seen Denny's work be warned that viewing it will leave you feeling quite inadequate. :-) ________________________________ ...
Dennis, I do in fact have a set of the Hardinge verniers, (don't remember where I got them years ago). The 200 is in great shape but some of the numbers are...
Hi Paul What diameter are the dials? Dennis ... From: houdini To: southbendmanual@yahoogroups.com Sent: Sunday, November 30, 2008 2:55 PM Subject: Re:...
Dennis, they are 2.5 in. in dia. as u can c, the 200 looks great, but the 100 is bad. do u restamp or re-engrave. i have a small pantograph. thanks, Paul ......
Hi Paul Yes yours are the ones off the Inch only HLV-H ones like yours would work great on a heavy ten or a 13 inch lathe. Just a little to big to put on...
Yeah, after looking they do seem a little large for the 9". My 10" Rockwell has direct reading dials so if your interested make me a fair offer and they are...
Thanks Dennis. I'm aware of the better transmittal of power .. I think these belts are good for somewhere between 5 and 10 HP "rubber side down". However, even...
... Was looking for info about my 13" lathe,and ran across the post about the expander screws.The actual answer is that yours (and mine) have no expander...
Hi Alan Think of it this way. The pitch diameter on the smooth side will be different than the pitch diameter of the grooved side. Pitch diameter on the...
Another way to look at it is that the smooth side is the part of the belt with the fibers in it so it does not stretch. When the rib side is out, the rubber is...
I've been looking to see what oil is proper for the South Bend 9" Workshop I have. I've read the oils SB recommends can be equaled in substitutes as follows: ...
I just noticed that some spammer has placed a junk file in the files section, leading to a website displaying "lovelies". While they may be desirable they are...
Well that was brutal. I had no idea how many of them were up there! Nearly all the sister groups were riddled with them. Deleting them one at a time was the...
